Envoy NT9010A Przewodnik Instalacji Pobierz pdf (Strona 44)

Chapter 2: Advanced Programming

Communicator Enabled/Disabled . . . . . . . . . . . . . . . . . . . Section [380], Option [1]

Pulse Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [380], Option [3]

Switch to Pulse Dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [380], Option [4]

Post Dial Wait for Handshake. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [161]

Maximum Dialing Attempts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [160]

Communicator Call Direction Options . . . . . . . . . . . . . . . . . Sections [361] to [368]

2.3.9

Communicator

Telep hone

Numbers

The system can call 3 different telephone numbers for communication to central

station. The 1st Telephone Number is the primary number, the 2nd Telephone

Number is the secondary number and the 3rd Telephone Number will back up

the 1st telephone number if enabled.

You can program the 1st Telephone Number using Flash Programming, or in the

Advanced Programming (section [301]). The 2nd and 3rd Telephone Numbers must

be programmed in the Advanced Programming sections.

NOTE: The 3rd telephone Number will NOT back up the 2nd telephone

Number.

If Alternate Dial is enabled the system will alternate between the 1st and 3rd tele-

phone numbers when attempting to call the central station. If disabled the system

will only attempt to call the 3rd telephone number after failing to communicate on

the 1st telephone number.

NOTE:For Alternate Dial to work properly the 3rd telephone Number must

be both enabled and programmed.

Telephone numbers can be up to 32 digits which will allow you to add special digits

if required. To program the telephone number enter numbers 0 through 9 as

required. The following is a list of HEX digits which can also be programmed and

the function they perform:

HEX (B) - simulates the [✱] key on a Touch-Tone telephone

HEX (C) - simulates the [#] key on a Touch-Tone telephone,

or end of telephone number marker

HEX (D) - forces the system to search for dial tone

HEX (E) - forces the system to pause for 2 seconds

HEX (F) - end of telephone number marker

1st telephone number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [301]

2nd telephone number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [302]

3rd telephone number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [303]

3rd telephone number enable . . . . . . . . . . . . . . . . . . . . . Section [380], Option [5]

Alternate Dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [380], Option [6]

2.3.10

Communicator

Account

Codes

The system Account Codes will be used by the NT9010 when communicating sys-

tem events (e.g. Low Battery, Test Transmission). This account code can be up to

four digits in length.

1 2 ... 39 40 41 42 43 44 45 46 47 48 49 ... 63 64

Komentarze do niniejszej Instrukcji

Brak uwag

Envoy NT9010A Przewodnik Instalacji Strona 44

Komentarze do niniejszej Instrukcji