Envoy NT9010A Przewodnik Instalacji Pobierz pdf (Strona 63)

Appendix E: WLS904P Wireless Motion Detector Installation Instructions

High Traffic Shutdown Mode

To prolong battery life, the motion detector uses a

feature called High Traffic Shutdown. When motion is

detected, the device will transmit to the receiver and

will then shut down for three minutes. If motion is

detected again during the shutdown time, the unit

will not transmit the event to the receiver. The detec-

tor will thus remain in the shutdown mode until three

minutes after the first motion detected was transmit-

ted. The detector will transmit detected motion every

three minutes.

The High Traffic Shutdown Mode affects testing the

motion detector in two ways:

When performing the module placement test,

the unit must be tampered by removing the unit from

the backplate and replacing it. The placement test

cannot be performed by creating motion in front of

the device.

When performing a system test, the unit must be

left idle for three minutes before testing can be per-

formed. Once three minutes has passed, create motion

in front of the detector to see if the device is both

detecting motion and transmitting to the receiver.

NOTE:Refer to the PC5132 and PC5010 Installa-

tion Instructions for UL/ULC requirements. For UL/

ULC installations where the WLS904P is used on

entry or exit delay zones, the entry delay must

not be longer than 39 seconds, and the exit delay

must not be longer than 54 seconds.

Motion Detector Transmission Delay

A motion detector transmission is always delayed by

six seconds. This is necessary to prevent false alarms

caused by a motion sensor transmitting before a delay

zone has a chance to report. This six-second delay

cannot be altered or disabled.

Walk Test Mode

The motion detector has a walk test mode which will

activate an LED for testing purposes. During normal

operation, the LED will not turn on.

To put the detector in walk test mode, create a

tamper by removing the detector from its backplate

and then replacing it. Each time the detector senses

motion, it will turn on the red LED. Five seconds after

motion is detected, the detector will send a signal to

the receiver, and the LED will flash rapidly 5 times. The

detector will be in walk test mode until it has sent 10

transmissions.

To verify the pet immunity of the detector place the ani-

mal(s) within the coverage area and then move out of the

zone. Encourage the pet to move around as it normally

would and ensure that it moves across the detection pat-

tern of the detector. Verify that no alarm is initiated.

To test for catch performance of humans, create

motion in the entire area where coverage is desired by

walking perpendicular to the lens pattern. Should the

coverage be incomplete, readjust or relocate the

detector.

NOTE:The Walk Test Mode will override the

High Traffic Shutdown Mode.

Battery Installation

• This system is designed to work with Eveready

Alkaline Energizer Batteries. Do not install any

other type. The reliability of the security system

depends on its batteries, and “no name” or

generic brand batteries may not provide the best

quality and dependability.

• Use fresh batteries. Most batteries have a ìbest

beforeî date printed on their packaging or on the

batteries themselves. Buy batteries that have a

“best before” date of two years or more from your

purchase date.

• When disposing of used batteries, follow the

instructions and precautions printed on the batter-

ies. Many cities and communities have collection

sites or services for used household batteries. Con-

tact your municipal offices for information on the

disposal of used batteries.

Remove the motion

detector from its mount-

ing plate by holding the

sensor by its sides and

pushing up. Install four

fresh Eveready Alkaline

Energizer AAA batteries.

Be sure to insert the bat-

teries in the proper orien-

tation. Replace the

sensor on its mounting

plate, making sure it snaps into place.

After all the batteries are installed, the detector will

take 60 seconds to warm up. During this time the LED

will flash slowly.

TOP VIEWSIDE VIEW

Detection Pattern

"Fast" Setting - 40ft x 40ft

"Slow" Setting - 35ft x 35ft

1 2 ... 58 59 60 61 62 63 64

Komentarze do niniejszej Instrukcji

Brak uwag

Envoy NT9010A Przewodnik Instalacji Strona 63

Komentarze do niniejszej Instrukcji